300-410 Real Exam Dumps Questions and answers 11-20

Get Full Version of the Exam
http://www.EnsurePass.com/300-410.html

Question No.11

Refer to the exhibit. An engineer is trying to redistribute OSPF to BGP, but not all of the routes are redistributed. What is the reason for this issue?

image

  1. By default, only internal routes and external type 1 routes are redistributed into BGP.

  2. Only classful networks are redistributed from OSPF to BGP.

  3. BGP convergence is slow, so the route will eventually be present in the BGP table.

  4. By default, only internal OSPF routes are redistributed into BGP.

Correct Answer: D

Question No.12

Which attribute eliminates LFAs that belong to protected paths in situations where links in a network are connected through a common fiber?

  1. shared risk link group-disjoint

  2. linecard-disjoint

  3. lowest-repair-path-metric

  4. interface-disjoint

Correct Answer: A

Explanation:

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_eigrp/configuration/xe-3s/asr1000/ire- xe-3s-asr1000/ire-ipfrr.html

Question No.13

Refer to the exhibit. In which circumstance does the BGP neighbor remain in the idle condition?

image

  1. if prefixes are not received from the BGP peer

  2. if prefixes reach the maximum limit

  3. if a prefix list is applied on the inbound direction

  4. if prefixes exceed the maximum limit

Correct Answer: D

Question No.14

Refer to the exhibit. An engineer is troubleshooting BGP on a device but discovers that the clock on the device does not correspond to the time stamp of the log entries. Which action ensures consistency between the two times?

image

  1. Configure the service timestamps log uptime command in global configuration mode.

  2. Configure the logging clock synchronize command in global configuration mode.

  3. Configure the service timestamps log datetime localtime command in global configuration mode.

  4. Make sure that the clock on the device is synchronized with an NTP server.

Correct Answer: C

Question No.15

Refer to the exhibit. What is the result of applying this configuration?

image

  1. The router can form BGP neighborships with any other device.

  2. The router cannot form BGP neighborships with any other device.

  3. The router cannot form BGP neighborships with any device that is matched by the access list named 鈥淏GP鈥?

  4. The router can form BGP neighborships with any device that is matched by the access list named 鈥淏GP鈥?

Correct Answer: A

Question No.16

Which command displays the IP routing table information that is associated with VRF-Lite?

  1. show ip vrf

  2. show ip route vrf

  3. show run vrf

  4. show ip protocols vrf

    Correct Answer: B

    Explanation: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/12- 2/50sg/configuration/guide/Wrapper-46SG/vrf.html#wp1045708

    Question No.17

    Refer to the exhibit. Which subnet is redistributed from EIGRP to OSPF routing protocols?

    image

    A.

    10.2.2.0/24

    B.

    10.1.4.0/26

    C.

    10.1.2.0/24

    D.

    10.2.3.0/26

    Correct Answer: A

    Question No.18

    Which configuration adds an IPv4 interface to an OSPFv3 process in OSPFv3 address family configuration?

    1. router ospfv3 1 address-family ipv4

    2. Router(config-router)#ospfv3 1 ipv4 area 0

    3. Router(config-if)#ospfv3 1 ipv4 area 0

    4. router ospfv3 1 address-family ipv4 unicast

Correct Answer: C

Explanation:

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_ospf/configuration/xe-3s/iro-xe-3s- book/ip6-route-ospfv3-add-fam-xe.html

Question No.19

Refer to the exhibit. Which statement about R1 is true?

image

  1. OSPF redistributes RIP routes only if they have a tag of one.

  2. RIP learned routes are distributed to OSPF with a tag value of one.

  3. R1 adds one to the metric for RIP learned routes before redistributing to OSPF.

  4. RIP routes are redistributed to OSPF without any changes.

Correct Answer: B

Question No.20

Refer to the exhibit. An IP SLA was configured on router R1 that allows the default route to be modified in the event that Fa0/0 loses reachability with the router R3 Fa0/0 interface. The route has changed to flow through router R2. Which debug command is used to troubleshoot this issue?

image

  1. debug ip flow

  2. debug ip sla error

  3. debug ip routing

  4. debug ip packet

Correct Answer: C

Get Full Version of 300-410 Dumps

Leave a Reply

Your email address will not be published. Required fields are marked *