300-425 Real Exam Dumps Questions and answers 1-10

Get Full Version of the Exam
http://www.EnsurePass.com/300-425.html

Question No.1

What is the recommended cell overlap when designing a wireless network for Cisco Hyperlocation?

A.

20%

B.

30%

C.

40%

D.

50%

Correct Answer: A

Question No.2

Which CLI command does an engineer use to validate that the redundancy peer of a Stateful Switchover pair of controllers is up and connected?

  1. rping

  2. ping

  3. eping

  4. mping

Correct Answer: B

Question No.3

An engineer must decide the cell overlap for a wireless voice deployment. Which Cisco measurement recommendation should be considered?

  1. The edge of the cell should be -67 dBm.

  2. The edge of the cell should be below 35 RSSI.

  3. The measurement should be done on the 2.4-GHz band.

  4. One AP should be deployed per 3000 square feet.

Correct Answer: A

Question No.4

Which UDP port numbers are used for exchange mobility packets in an AireOS wireless deployment?

  1. UDP 16666 for control plane, EoIP (IP protocol 97) for data plane

  2. UDP 16668 for control plane, UDP 16667 for data plane

  3. UDP 16667 for control plane, UDP 16666 for data plane

  4. UDP 16666 for control plane, UDP 16667 for data plane

Correct Answer: D

Question No.5

Which statement about AP failover priority for access points when configured with priority 1 or 4 is true?

  1. When configured with priority 1, the access point is assigned with the highest priority level and it is marked as critical. This access point fails over before other access points with the lower priority when there is primary controller failure.

  2. When configured with priority 4, the access point is assigned with the highest priority level and it is

    marked as critical. This access point fails over before other access points with the lower priority when there is primary controller failure.

  3. When configured with priority 4, the access point is assigned with the lowest priority level and it is marked as low. This access point fails over after other access points with the higher priority when there is primary controller failure.

  4. When configured with priority 1, the access point is assigned with the medium priority level and it is marked as medium. This access point fails over after other access points with the higher priority when there is primary controller failure.

Correct Answer: B

Question No.6

As part of a wireless site survey in a hospital, an engineer needs to identify potential Layer 1 interferers. In which two areas is the engineer most likely to find sources of 2.4 GHz and 5 GHz RF noise? (Choose two.)

  1. magnetic resonance imaging

  2. kitchen

  3. Gamma Knife radiation treatment

  4. X-ray radiography

  5. patient room

Correct Answer: BE

Question No.7

A wireless network consultant must assess an existing wireless LAN controller. Which section must the consultant check before replacing the old APs with APs that are IEEE 802.11ac-capable?

  1. number of AP licenses

  2. controller PSU

  3. throughput capacity

  4. software version

Correct Answer: A

Question No.8

A rapidly expanding company has tasked their network engineer with wirelessly connecting a new cubicle area with Cisco workgroup bridges until the wired network is complete. Each of 42 new users has a computer and VoIP phone. How many APs for workgroup bridging must be ordered to keep cost at a minimum while connecting all devices?

A.

4

B.

5

C.

6

D.

7

Correct Answer: A

Question No.9

A network engineer is working on a design for a wireless network that must support data, voice, and location services. To support these services, which access point placement must the engineer use?

  1. corner only

  2. perimeter and corner

  3. perimeter only

  4. indoor and outdoor

Correct Answer: C

Question No.10

An engineer has successfully configured high availability and SSO using two Cisco 5508 Wireless LAN Controllers. The engineer can access the Active Primary WLC, but the Secondary Standby WLC is not accessible. Which two methods allow access to the standby unit? (Choose two.)

  1. via the console connection

  2. SSH to the redundancy management interface of the primary WLC

  3. SSH to the service port interface

  4. SSH to the virtual interface of the secondary WLC

  5. SSH to the management interface of the primary WLC

Correct Answer: AC

Get Full Version of 300-425 Dumps

Leave a Reply

Your email address will not be published. Required fields are marked *